Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Duncanville: What to Know First
FAAC gate installation in Duncanville typically runs $1,850 to $6,400 depending on whether we’re hanging a single swing gate or a full double-gate slide system with operators, safety edges, and keypad entry. Most FAAC installations are completed in one visit, and the price is settled in writing before we turn the first bolt. We’re an independent FAAC service provider, not an authorized dealer, which means we repair and replace what’s failing without pushing a full system swap when a single board or limit switch would do the job.
This page is for FAAC owners in Duncanville who need a gate hung, an operator mounted, or a complete system installed without the runaround. Call (903) 532-2236 and a live person answers, day or night.
How FAAC Products Fail - and How We Fix Them
- FAAC 455 D control board capacitor burn-out: The 455 D is common on Duncanville swing gates, and the electrolytic capacitors on the board dry out after six to ten years of Texas heat. The gate will click but not move, or open halfway and stall. We replace the capacitor set or the board itself with OEM-grade components, then re-tune the torque limits so the motor doesn’t work harder than it should on a 100-degree afternoon.
- FAAC 750 sliding operator limit switch drift: On sliding gates, the 750’s magnetic limit switches can wander out of position after years of cycles, so the gate over-travels and slams the end stop. Homeowners hear it before they see it. We reset the limits, inspect the rack for wear, and adjust the chain tension so the next ten thousand cycles don’t beat the gearcase to death.
- FAAC S418 and C720 hydraulic locking failure: These hydraulic operators should hold a gate closed under pressure, but a worn seal or low hydraulic fluid means the gate drifts open on its own. That’s a security issue on a driveway. We rebuild or replace the cylinder, flush the system, and set the thermal bypass so a Duncanville summer doesn’t cook the oil and leave the gate limp.
- Photocell misalignment from gate-post settling: Duncanville’s clay soil shifts with every wet-dry cycle, and a post that settles half an inch throws the FAAC photocell beam out of line. The gate reverses mid-cycle and won’t close. We shim and re-align the posts, then run a full safety reverse test so the gate holds a solid beam every time.
- E024S underground operator water ingress: FAAC’s below-ground swing operators are excellent machines, but the lid seal can fail after a decade in North Texas downpours, letting water flood the module. We dry out the pit, replace the seal, and swap any corroded motor brushes. If the pit drainage is bad, we’ll say so before reinstalling anything, because a wet operator won’t last a season.
Our FAAC Gate Installation Process
Every FAAC job in Duncanville follows the same path, whether it’s a new S418 on a single swing gate or a full 844 slide system on a double driveway.
- 1
Call and tell us what the gate is doing, or not doing. Victor Salinas grew up off Clark Road, and he’ll ask the questions that matter over the phone before we schedule anything.
- 2
Site visit and honest assessment. We measure the gate, check the posts for plumb, and look at what operator is already there. If a repair extends the life by years, we’ll say so. If replacement is the right call, we’ll explain why in plain English.
- 3
Written price before work starts. No hourly mystery, no upcharge surprises. The number we quote is the number on the invoice.
- 4
Installation with OEM or equivalent parts. FAAC boards, limit switches, and hydraulic components get matched to the model. We don’t force aftermarket parts where the OEM part is the reliable choice.
- 5
Full cycle testing under load. We test the gate through thirty or forty cycles, adjust the soft-start and braking, verify safety edge sensitivity, and check the force reversal. We also test the manual release so you know what to do when the power’s out.
- 6
Cleanup and the 90-Day Done Right Promise. We walk the site with you, show you what we did, and hand you the written guarantee. If anything’s not right within 90 days, we come back and make it right.
What FAAC Gate Installation Costs in Duncanville
Here’s what we see across Duncanville driveways. These are installed prices, not parts-only.
- Hang and align one existing gate (no operator): $250 to $600
- New FAAC single swing gate with S418 operator and two remotes: $1,850 to $3,200
- New FAAC double swing gate with dual operators and safety edges: $3,400 to $5,800
- New FAAC sliding gate with 750 operator and rack: $2,600 to $4,900
- Full system with keypad, loop detector, and phone entry: $4,500 to $6,400
What moves the price is gate weight, post condition, and whether we’re running conduit and power or tying into an existing electrical line. Estimates are free, and the figure is agreed before any work begins. Call (903) 532-2236 for an exact quote.
Why Duncanville Homeowners Call Ironworks Gate Co. for FAAC Work
We’ve been serving the neighborhoods around Duncanville for over 42 years, and we plan to be here another forty. When a FAAC operator gives out, most companies want to sell you whatever’s on their truck. We carry the knowledge to service nine brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so we diagnose and repair what’s actually on the driveway instead of swapping good equipment for convenience. Every job is protected by the 90-Day Done Right Promise, written plainly with no fine print and no argument. Our technicians are background-checked and uniformed, working in your home the way they would work in their own mother’s. A live person answers the phone 24 hours a day, 7 days a week. Not a voicemail tree, not a call center. A person.
FAQs
As an independent FAAC service provider, our installation doesn’t void the manufacturer warranty on parts, but FAAC’s stated policy is that installation by a non-authorized technician may affect warranty claims on labor. We’re upfront about this before we start. Most Duncanville homeowners we work with have gates well past any warranty window anyway, so the 90-Day Done Right Promise is the guarantee that actually matters. Call (903) 532-2236 and we’ll explain your specific situation.
Yes, and we do it often. The gate itself just needs to be structurally sound and hung on solid posts. We’ll check the hinge welds, post depth, and gate weight before recommending an operator, because a FAAC S418 on a sagging gate will tear up the operator in a season. If the gate needs weld repair or post work, we handle that in the same visit.
If the gate is stuck open or stuck closed, call (903) 532-2236 and a live person answers around the clock. Most Duncanville emergency calls are scheduled same-day, and many repairs are completed in a single visit. We keep common FAAC boards, limit switches, and hydraulic components on the truck specifically because a gate that won’t close is a security problem, not a convenience problem.
Depends on the operator and what’s failed. A FAAC 455 D with a smoked capacitor board is usually a $200 to $450 repair and will run for years. A hydraulic operator with a scored cylinder, a roasted motor, and a dead control board all at once is the point where replacement makes more financial sense. We’ll lay out both numbers and let you decide with full information.
Yes. We run conduit, pull wire, set the breaker, and install all required safety equipment including photocells, safety edges, and the force-reversal calibration. Duncanville doesn’t require a separate gate permit for most residential work, but we build every installation to Texas electrical code whether the inspector is watching or not.
Call Ironworks Gate Co. for FAAC Gate Installation in Duncanville
If your FAAC gate is down or you’re planning a new installation, call us before you guess. Tell us what it is doing - or not doing - and we will go from there. We’ll give you an honest assessment over the phone, a written price before any work starts, and a gate that closes like the day it was hung. Reach us at (903) 532-2236 for a free estimate.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Duncanville and nearby areas.